Just How To Install A Bath Tub (For Novices).
Just How To Install A Bath Tub (For Novices).
Blog Article
Just about everyone has their personal piece of advice in relation to Installing A Bathtub.
Mounting a tub isn't specifically rocket science, yet it does require solid plumbing, woodworking, and in some cases, tiling abilities. Replacing an old tub with a new one is likewise a reasonably challenging task. If the old tub is easily accessible, the project can relocate speedily; if you have to open up a wall surface to remove the old bathtub and also position the brand-new bath tub, the task is a lot harder. In either situation, the task is within a house handyman's abilities, although you will certainly need an assistant to vacate the old tub and set in the brand-new one. Make sure you have qualified on your own for the work and are comfortable trying it. As opposed to hiring a specialist to take control of a halfway-completed project, it is better to think about using one before you begin. Possibilities are you might require a professional plumber to make tube connections.
This post will assist you mount a brand-new bathtub in your restroom if you have actually currently acquired a new tub and don't require to transform the setup of your previous water pipes.
Your tools and material checklist must consist of the following:
Getting ready for the Setup
To start with, the sustaining structure supplied with the bathroom must be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is essential to ensure that if the tap includes a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps unit to prevent pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet with the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you use every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its last placement.
Removing Old Taps
If you need to change old faucets with new ones as a part of your installment, after that the first thing you ought to do is disconnect the water. After doing so, switch on the taps to drain pipes any type of water staying in the system. The process of getting rid of the existing taps can be quite bothersome because of the limited access that is often the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the faucets. Have a cloth all set for the staying water that will certainly originate from the pipes. As soon as the supply pipes have actually been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. As soon as the taps have been eliminated, the holes in the bath/basin will need to be cleaned of any type of old sealing substance.
Before carrying on to fit the brand-new taps, contrast the pipe links on the old taps to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Installing the Tub
Using the two wood boards under its feet, place the bath tub in the required setting. The wooden boards are valuable in equally spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four tiny points.
The next objective is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the level and changing the feet on the bath tub until the level reviews level.
To set up faucets, fit the bottom of the furthest adaptable tap connector to the proper supply pipeline by making a compression join; after that do the very same for the other tap.
Activate the water supply and inspect all joints and also brand-new pipework for leakages as well as tighten them if essential. Fill the tub as well as also inspect the overflow electrical outlet and the regular electrical outlet for leaks.
Lastly, fix the bath paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the bathtub ought to wait till the bathtub has been utilized at the very least once as this will certainly settle it into its last placement.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and the other end supplies a link to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly call for reducing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the tap in the mounting hole in the bath/basin ensuring that the washing machines remain in area in between the tap as well as the sink. Secure the tap in position with the supplier given backnut. As soon as the faucet is safely in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet adapters. The previous type should be connected to the faucet finishes first, tightening just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bathroom satisfies the tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to crack an inflexible seal, creating the water to permeate the wall in between the bath and the tiling, bring about issues with dampness and also possible leakages to the ceiling below.
You can choose from a selection of coloured sealants to blend in your components as well as fittings. They are marketed in tubes and cartridges, and also can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to always load the tub with water before securing, to enable the movement experienced when the bathtub remains in use. The sealer can split fairly very early if you do not take into consideration this motion before securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise conveniently offered on the market. It is a good idea to fit the tiles making use of water-resistant or waterproof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I discovered that page about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when looking around the search engines. Sharing is caring. Helping people is fun. I treasure reading our article about Installing A Bathtub.
Schedule Appointment Now Report this page